Extron DTP DVI 330 TX - Long Distance DTP Transmitter for DVI

Description

Extron DTP DVI 330 TX - Long Distance DTP Transmitter for DVI
The Extron
DTP DVI 4K 330 Tx
is a long distance transmitter for sending DVI‑D video, audio, and bidirectional RS‑232 and IR signals up to 330 feet (100 meters) over a shielded CATx cable to Extron DTP
®
330-enabled products. It provides an effective means for extending single link DVI‑D or HDMI signals. In addition, the DTP DVI 4K 330 Tx accepts analog stereo audio signals for simultaneous transmission over the same shielded twisted pair cable. It supports video signals at resolutions up to 4K. The transmitter is equipped with a buffered DVI loop-through output to support a local computer monitor. The compact enclosure size and remote power capability make the DTP DVI 4K 330 Tx ideal for discreet placement in lecterns, beneath tables, or wherever needed to meet application requirements.
Frame rate
1
24, 25, 30, 50, or 60 fps
Chroma sampling
1
4:4:4, 4:2:2, or 4:2:0
Color bit depth
1
8 bits per color
Signal type
HDMI 1.4, HDCP 2.3
Max. video data rate
10.2 Gbps (3.4 Gbps per color)
Video
Maximum data rate
10.2 Gbps (3.4 Gbps per color)
Maximum pixel clock
300 MHz
Resolution range
Up to 2560x1600* @ 60 Hz or
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz,
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(* reduced blanking)
Color bit depth
8, 10, or 12 bits — subject to the maximum data rate limit
Formats
RGB and YCbCr digital video
Standards
DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E
Video input — transmitter
Number/signal type
1 single link DVI-D (or HDMI*) input
1 single link DVI-D (or HDMI*) local loop-through
Connectors
2 female DVI-I
Interconnection between transmitter and receiver
Connectors
1 female RJ-45 per unit
Termination standard
TIA/EIA T568B
Signal transmission distance
1080p @ 60 Hz
Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
2560x1600 @ 60 Hz
Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
4K/UHD @ 30Hz and 60 Hz
Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
Cable requirements
Solid conductor, 24 AWG or better
Cable recommendations
400 MHz bandwidth, STP (shielded twisted pair)
NOTE
Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Video output — receiver
Number/signal type
1 single link DVI-D (or HDMI*)
Connectors
1 female DVI-I
Audio
Gain
Unbalanced output: 0 dB; balanced output +6 dB
Frequency response
20 Hz to 20 kHz, ±0.5 dB
THD + Noise
0.03% @ 20 Hz to 20 kHz at maximum output
S/N
>90 dB, at maximum output (15 dBu), balanced (unweighted)
Stereo channel separation
>80 dB @ 1 kHz to 20 kHz
Audio input
Number/signal type
1 PC level stereo, unbalanced
NOTE
Analog audio is not embedded onto the digital video signal.  Embedded digital audio is not de-embedded from the digital video signal.
Connectors
(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)
Impedance
>10k ohms, DC coupled
Nominal level
-10 dBV (316 mVrms)
Maximum level
+6 dBV (unbalanced)
NOTE
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
Number/signal type
1 stereo (2 channel), balanced/unbalanced
Connectors
(1) 3.5 mm captive screw connector, 5 pole
Impedance
50 ohms unbalanced, 100 ohms balanced
Gain error
±0.1 dB channel to channel
Maximum level (600 ohm)
>+11 dBu, balanced
Communications — external device (pass-through, unidirectional or bidirectional)
Serial control port input/output
Transmitter
RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port)
Receiver
1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input
Transmitter
1 set of proprietary signals on a female RJ-45 jack
Receiver
RS-232 via a 3.5 mm, 3 pole captive screw connector
Baud rate and protocol
300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity
Serial control pin configuration
1 = Tx, 2 = Rx, 3 = Gnd
IR control port
(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
IR control pin configuration
3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
Power supply
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts
Power consumption
Transmitter
Device
3.4 watts
Device and power supply
4.8 watts
Remote power budget
12 watts
Receiver
Device
4.2 watts
Device and power supply
5.8 watts
Remote power budget
12 watts
NOTE
Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
Temperature/humidity
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling
Convection, no vents
Thermal dissipation
Transmitter
Device
10.3 BTU/hr
Device and power supply
15.1 BTU/hr
Receiver
Device
13.0 BTU/hr
Device and power supply
18.6 BTU/hr
Mounting
Rack mount
Yes, with optional 1U high rack shelf
Furniture mount
Yes, with optional under-desk mounting kit
Enclosure type
Metal
Enclosure dimensions
Transmitter
1.0" H x 4.3" W x 3.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.)
Receiver
1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.)
Product weight
Transmitter
0.5 lbs (0.3 kg)
Receiver
1.0 lb (0.5 kg)
Regulatory compliance
CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI,
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply.
Complies with the appropriate requirements of RoHS, WEEE
NOTE
**CE and FCC testing is conducted with STP (shielded twisted pair) I/O cable.
Product warranty
3 years parts and labor
Everlast power supply warranty
7 years parts and labor
NOTE
All nominal levels are at ±10%.
NOTE
Specifications are subject to change without notice.